Step-By-Step Instructions Of Glass

Glass – How to Buy It

A homeowner can get a lot for his money or a little when he buys glass for windows, doors or partitions. But if he knows which glass will do what, and how to buy it, he won’t pay double or three times prices for plate glass when he could have used heavy published glass, nor will he waste money by ordering glass by the randburg glass published when he could have used a case.

Window glass, also called published glass, is the most commonly used in the house. In fact before glass walls and picture windows were used it was usually the only kind. It comes in two thicknesses, single strength and double strength; and in two qualities, A and B.

Grades A and B differ only in the number of small disorders and swells. However, the difference is not ordinarily noticeable, and many dealers don’t even stock A quality because they just don’t believe that it is worth a 25 percent premium.

Whether to use single or double strength depends mainly on window size. A good rule to follow is to apply double strength for anything over about two feet rectangular. How large can double strength glass be? If winds don’t exceed 70 mirielle. p. h., double strength glass may be used in sizes up to 38″x48″, or 34″x72″.

The next price jump to amazingly published or plate glass is very sharp. If you want a window wall consider the likelihood of working it out using the indicated dimensions of double strength instead of plate glass. This can be most attractive and at about one-fourth the cost. Go right across the room with 30″x72″ double-strength glass placed vertically. The space of approximately 30″ to the floor can be plain wall or used for built-in bookcases, cabinets or ventilating louvers.

Case Lots

Buying window glass by the case is one way to save money. Glass by the case doesn’t cost much more than half as much as by the published. It’s also better to handle. At economical prices you can afford to use glass liberally in anything you build or remodel or enclose. And, buying by the case does not mean you’re stockpiling it for many years. Usually a case of window glass is whatever number of sheets comes nearest to totaling 50 rectangular feet. Cases of very large sheets contain 100 rectangular feet.

Amazingly published, which is heavy window glass of good quality, is the economical thing to buy when the opening is too big for double strength.

Plate glass, which is shiny to optical flawlessness, may be 1/8″ thick or for a big view window, 1/4″ thick. If you have a long-distance view through your window, you will need plate glass. Otherwise you can use amazingly published; for short mileage you will never notice the slight waviness.

For plate and usually amazingly published, in sizes too big for you to handle and too expensive for you to risk breaking, you must figure on paying a higher installed price, which includes a high priced labor cost.

Heat-absorbing plate glass, while no substitute for air cooling, does screen out approximately 29% of the sun’s heat. It is used in gulf windows of seaside homes, as well as in car windows. It costs about 5/2 times as much as regular plate glass.

Unknown glass is used where you want light but no visibility. For example, a wall of it might be just the thing for a basements recreation room where perhaps the basements is used as a garage or working area. For this you would need the thick kind, say 3/8″. Thinner figured glass serves for entrance panels, cupboard doors and shower enclosures.

Transparent mirror glass is often used for one-way vision in entrance doors. Ready-made it is most expensive, but a glass dealer who makes mirrors can usually prepare it for you at about half the price.

Insulating glass is the modern, superior replacement for ordinary windows plus storm sash. Like any insulation, it usually pays for itself over the years in fuel savings as well as comfort. It consists of two or three panes sealed in units, with air spaces between the panes. A typical double glazed unit has two sheets of 1/4″ plate glass with a 1/2″ air space between. Originally all insulating units were made of plate glass, but it is now manufactured in window glass as well. Until you need large windowpanes, you can save about one- third utilizing the window glass kind.

Glass Blocks

In the long list of building materials, glass blocks rank as one of the most versatile. They can be used for exterior as well as interior walls or for partition walls that do not go entirely to the hallway.

Glass blocks provide light plus privacy. They come in many sizes and shapes and there are special blocks intended to control sunshine. Furthermore, glass blocks are easy to maintain and special units are available to provide ventilation through glass block walls.

Glass blocks can be installed within a wooden frame or in a bed of mortar. Once you discover how to set class blocks in mortar – a project you might want to undertake to exchange a preexisting basements window with glass blocks – then you will be able to handle glass blocks within a frame inside. Literature on interior mounting of glass blocks is readily available from glass block manufacturers.

How to work with Glass Block

The proper mortar materials and mix are important whether for laying bricks or glass blocks.

The proper mortar materials are Portland cement, hydrated lime, sand, water, and waterproofing compound. The addition of an integral water-proofer of the water-repellent type is an added measure to insure watertight joints. Manufacturer’s specifications concerning the use of this material should be followed very closely. Where a waterproof masonry mortar is used, no additional water-proofer should be added to the mix. For better results, accelerators and antifreeze compounds should not be used.

ACCURATE WAY OF MEASURING

The accurate way of measuring of materials is important. Generally a 1-1-4 mortar mix is satisfactory. However, reasonable variations from the mix are permitted and allowable limits are covered by manufacturer’s specifications.

MORTAR CONSISTENCY

The consistency of the mortar mix has a direct supporting on the strength and weather-proof ness of the joints. Since glass blocks have no suction like bricks, the mortar must be drier… it should not flow or have too much drawback. Too wet a mixture makes it extremely difficult to get proper angle of block joints, and cleaning time is greatly increased. The mix should he not too dry, not too wet, but just right. Here is a good thing to remember: Do not re-temper mortar after the ¡niti. il set has taken place.

PANELS OF GLASS BLOCK 35 SQ. FT. OR LESS

In this type of construction the absolute maximum area is 35 rectangular feet with maximum width 5′ and height 7′. The typical practice is to apply an expansion space at the side jambs of all glass block panels. However, for small panels as illustrated here the blocks can be mortared in solid at the side jambs. It is necessary, however, to keep a finger space between brick withes about 3/4″ deep. Web template the mortar to get into at jamb and secure panel.

Glass block panels, regardless of area or size, are nonload supporting and require space at the head to take care of expansion and lintel deflection.

PANELS OF GLASS BLOCK BETWEEN 25 AND 100 SQ. FT.

Where it is desirable to show the full face of the block panel, chases cannot be used for lateral support. Proper support can be had by using wall anchors if the area is not over 100 rectangular feet and neither panel dimension is over 10′. The wall anchors should be spread out 24″ apart – and occur in the same joint as the wall tie. To permit free movement of the panel, the anchors are crimped or bias in the expansion space. As a space for calking must be provided, a standard expansion line is easily cut to 3″ width to be inserted between the anchors with gobs of asphalt emulsion. Local code authorities in some areas may restrict the use of wall anchor construction.

Glass Cutter machine

This tool is used to cut glass to size. Usually, a glass cutter machine has a small rotary wheel or diamond from the handle.

There are also glass cutting bits for drilling holes in glass. These special bits require the use of a lubricant while cutting. It is best to make a ‘well’ or ‘dish’ around the spot to be drilled by using putty to form the walls. Then fill a little turpentine or oil into the ‘dish’ to lubricate the bit though it is cutting through the glass.

Glass Cutting

While you can usually buy glass cut to size, baby it is necessary to cut the glass yourself. When you watch an expert cut glass, it looks easy enough. Well, here’s how to cut glass like an expert.

Leave a Reply

Your email address will not be published. Required fields are marked *